 |
| -TiteLite- Motorcycle License Plate Lights - Acorn Head Polished Finish (pair) Item #: 030311 |
$29.98
|
TiteLite License Plate Light kits feature a right-angle LED for direct illumination of your license plate. Super bright LEDs are extemely efficient and emit a higher degree of light in a desired location than incandescent lamps. Since there is no filament that can be damaged, LEDs are incredibly durable - virtually shock and vibration-proof!
The clear epoxy covered lens offers waterproof protection.
Temperature resistant
Low power consumption
Low heat output
No damaging UV emissions
Thread pitch 5/16" x 18
 |
|
 |
| -TiteLite- Motorcycle License Plate Lights - Domed Head Polished Finish (pair) Item #: 030310 |
$24.98
|
TiteLite License Plate Light kits feature a right-angle LED for direct illumination of your license plate. Super bright LEDs are extemely efficient and emit a higher degree of light in a desired location than incandescent lamps. Since there is no filament that can be damaged, LEDs are incredibly durable - virtually shock and vibration-proof!
The clear epoxy covered lens offers waterproof protection.
Temperature resistant
Low power consumption
Low heat output
No damaging UV emissions
|
|
 |
| -TiteLite- Motorcycle License Plate Lights - Domed Head Satin Finish (pair) Item #: 030302 |
$22.98
|
TiteLite License Plate Light kits feature a right-angle LED for direct illumination of your license plate. Super bright LEDs are extemely efficient and emit a higher degree of light in a desired location than incandescent lamps. Since there is no filament that can be damaged, LEDs are incredibly durable - virtually shock and vibration-proof!
The clear epoxy covered lens offers waterproof protection.
Temperature resistant
Low power consumption
Low heat output
No damaging UV emissions
|
|
 |
| FLASH RATE CONTROLLER KIT Item #: RU35955 |
$33.14
|
| When you install LED signals in replacement of stock ones you get a fast flashing (usually 3x faster), this FLASHER CONTROLLER will bring the flash rate back to 60 fpm (approx). This kit contains a module that controls one right and one left LED turn signal. It increases the impedance of the circuit so that your OEM flasher works at the normal frequency. The module should be installed with one lead wire to the left signal wire, one lead wire to the right signal wire, and a third wire to GND. Polarity needs to be observed.
|
|
 |
| LED Easy Plug Relays - HONDA Item #: RU35956 |
$38.56
|
HONDA, will replace oem relay to slow down the flash rate.
When you install Led signals in replacement of stock ones you get a fast flashing (usually 3x faster), this LED EASY PLUG RELAY will bring the flash rate back to 60 fpm (approx).
This unit will control all 4 signals at a time, only one relay is needed on a bike, there is no connections to do, it’s a plug & play unit.
Honda - WARNING: This unit will NOT work with the CBR600RR |
|
 |
| LED Easy Plug Relays - KAWASAKI Item #: RU35957 |
$38.56
|
KAWASAKI, will replace oem relay to slow down the flash rate.
When you install Led signals in replacement of stock ones you get a fast flashing (usually 3x faster), this LED EASY PLUG RELAY will bring the flash rate back to 60 fpm (approx).
This unit will control all 4 signals at a time, only one relay is needed on a bike, there is no connections to do, it’s a plug & play unit.
Kawasaki - Almost Universal |
|
 |
| LED Easy Plug Relays - YAMAHA Item #: RU35958 |
$38.56
|
YAMAHA, will replace oem relay to slow down the flash rate.
When you install Led signals in replacement of stock ones you get a fast flashing (usually 3x faster), this LED EASY PLUG RELAY will bring the flash rate back to 60 fpm (approx).
This unit will control all 4 signals at a time, only one relay is needed on a bike, there is no connections to do, it’s a plug & play unit.
Yamaha - Almost Universal |
|
|
|
|
|
|
|
|
|
|
|
 |
| MINI FAIRING LED 60mm/12mm 1 WHITE LED Item #: 07-7000W |
$33.48
|
| These small sized lights are only 1/2 x 2 and can be mounted on any flat surface with the self adhesive backing. The single white LED lights the full length of the clear body. Mount a pair to your undertail cowl to provide some light on the license plate. 12v - 2 wire. Sold in pairs.
|
|
 |
| Puig Fender LED License Light Item #: PFL4646N |
$22.95
|
| New Puig Fender light available and in stock. It is an LED light in a black housing. Will fit all Puig Fender Kits. No drilling required. |
|
|
|
 |
| ROUND TAIL LIGHT ASSEMBLY - CLEAR LENS/RED BULB Item #: 07-8011C |
$37.35
|
| The round taillights are replacements for the lights used on many of the Targa Undertail Cowls. These taillights have an aluminum housing and are available in either red lens with clear bulbs (07-8010R) or clear lens with red bulbs (07-8011C). Sold individually. |
|
 |
| ROUND TAIL LIGHT ASSEMBLY - RED LENS/CLEAR BULB Item #: 07-8010R |
$37.35
|
| The round taillights are replacements for the lights used on many of the Targa Undertail Cowls. These taillights have an aluminum housing and are available in either red lens with clear bulbs (07-8010R) or clear lens with red bulbs (07-8011C). Sold individually. |
|
 |
| Rumble - Kawasaki ZX10R (06-07) Led ''Backdraft'' Signals Item #: RU35009 |
$235.98
|
Great value never looked so good. The BACKDRAFT rear signals will gives your bike a high-performance look...
If a big wing signal is not your thing, turn some heads and inflict some attitude on your ride with our new led BACKDRAFT signals, they are 5 times lighter then stock ones and merge perfectly with the stock bodywork these ABS made signals cap come painted factory match to your bike and they use 18 amber wide angle bright led.
Installation couldn't get any easier utilizing existing attachment points, you will only have to do the connections between stock wiring and your new signals.....
|
|
 |
| Rumble - KAWASAKI ZX14 2006 LED ''Backdraft'' Signals Item #: RU34969 |
$235.98
|
Great value never looked so good. The BACKDRAFT rear signals will gives your bike a high-performance look...
If a big wing signal is not your thing, turn some heads and inflict some attitude on your ride with our new led BACKDRAFT signals, they are 5 times lighter then stock ones and merge perfectly with the stock bodywork these ABS made signals cap come painted factory match to your bike and they use 21 amber wide angle bright led,
Installation couldn't get any easier utilizing existing attachment points, you will only have to do the connections between stock wiring and your new signals.....
|
|
 |
| Rumble - SUZUKI GSXR1000 (05-06) LED ''Backdraft'' Signals Item #: RU35650 |
$235.98
|
Great value never looked so good. The BACKDRAFT rear signals will gives your bike a high-performance look...
If a big wing signal is not your thing, turn some heads and inflict some attitude on your ride with our new led BACKDRAFT signals, they are 5 times lighter then stock ones and merge perfectly with the stock bodywork these ABS made signals cap come painted factory match to your bike and they use 18 amber wide angle bright led,
Installation couldn't get any easier utilizing existing attachment points, you will only have to do the connections between stock wiring and your new signals.....
|
|
 |
| Rumble - SUZUKI GSXR600 2006 LED ''Backdraft'' Signals Item #: RU34967 |
$235.98
|
Great value never looked so good. The BACKDRAFT rear signals will gives your bike a high-performance look...
If a big wing signal is not your thing, turn some heads and inflict some attitude on your ride with our new led BACKDRAFT signals, they are 5 times lighter then stock ones and merge perfectly with the stock bodywork these ABS made signals cap come painted factory match to your bike and they use 18 amber wide angle bright led,
Installation couldn't get any easier utilizing existing attachment points, you will only have to do the connections between stock wiring and your new signals.....
|
|
 |
| Rumble - SUZUKI GSXR750 2006 LED ''Backdraft'' Signals Item #: RU34968 |
$235.98
|
Great value never looked so good. The BACKDRAFT rear signals will gives your bike a high-performance look...
If a big wing signal is not your thing, turn some heads and inflict some attitude on your ride with our new led BACKDRAFT signals, they are 5 times lighter then stock ones and merge perfectly with the stock bodywork these ABS made signals cap come painted factory match to your bike and they use 18 amber wide angle bright led,
Installation couldn't get any easier utilizing existing attachment points, you will only have to do the connections between stock wiring and your new signals.....
|
|
 |
|
 |
| RUMBLE IMPORT - WHITE LED PLATE LIGHT (3 LED`S) Item #: CY25760 |
$53.88
|
This white 3 LED light was created to illuminate the license plate installed with undertail kit or custom license bracket.
The bracket mounts behind the license plate with 2 sided tape (included) and screw into the 12v light frame. - connect to license light wires. Does not include License bracket. |
|
 |
| SIGNAL SPEED CONTROLLER for LED SIGNALS Item #: 07-H505R-2 |
$42.44
|
| Kit contains 2 resistors, for both Left and Right side.
LED lights have extremely low current draw and will flash at 2 times the normal rate when used as turnsignals, which may be illegal in some areas. To bring the flash rate to the normal 85 flash per minute (avg) we offer a flash Controller that is simply wired into each LED signal on the bike. NOTE: for use only in the signal circuit, not on continuous running lights. |
|
 |
|
 |
| Targa Led Turn / Signal License Mount Assy - Red Item #: 07-600R |
$60.57
|
| Install these super bright LEDs on your license plate bracket for use as marker or signal lights. Simple installation by placing the stamped bracket between your license plate and the bracket, wire to your existing signal wires and youre ready to go. 12v - 2 wire. |
|
 |
| Targa Led Turn / Signal License Mount Assy - Amber Item #: 07-600A |
$60.57
|
| Install these super bright LEDs on your license plate bracket for use as marker or signal lights. Simple installation by placing the stamped bracket between your license plate and the bracket, wire to your existing signal wires and youre ready to go. 12v - 2 wire. |
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
| TARGA 5 LED SIGNAL W/ BLACK HOUSING - AMBER Item #: 07-5873A |
$40.31
|
| These super bright LEDs are mounted in a small compact housing, measuring 1 1/2 wide x 7/16 hi x 3/4 deep and are available with red or amber LEDs. They are sold individually for custom installation applications. Sold individually (each price)
|
|
 |
| TARGA 5 LED SIGNAL W/ BLACK HOUSING - RED Item #: 07-5875R |
$40.31
|
| These super bright LEDs are mounted in a small compact housing, measuring 1 1/2 wide x 7/16 hi x 3/4 deep and are available with red or amber LEDs. They are available individually for custom installation applications. Sold individually (each price)
|
|
 |
| TARGA 5 LED SIGNAL W/ FLAT PANEL MOUNT - AMBER Item #: 07-5001A |
$60.57
|
| The 90o 5 LED Marker Lights can be mounted with 2 sided adhesive foam (included) or be screw mounted, to your rear tail, undertail, under the front fairing edge or any flat area to provide additional lighting. 12v - Sold in pairs. |
|
 |
| TARGA 5 LED SIGNAL W/ FLAT PANEL MOUNT - RED Item #: 07-5002R |
$60.57
|
| The 90o 5 LED Marker Lights can be mounted with 2 sided adhesive foam (included) or be screw mounted, to your rear tail, undertail, under the front fairing edge or any flat area to provide additional lighting. 12v - Sold in pairs. |
|
|
|
 |
| TARGA COMBINATION REAR LED LIGHT, BLACK w/ SWIVEL BASE Item #: 07-5010B |
$49.67
|
COMBINATION LED LIGHT W/ SWIVAL BASE - TAILL/STOP/SIGNAL
This Compact LED Light module has 6 Red center LEDs for Taillight/Stop light function and 8 amber LEDs (4 left/4 right) for signal markers. This LED Light unit is in a sleek black housing with a clear lens and is only 6 1/2 wide and 7/8 high. Available in two styles, Swivel base mount for undertail, fender or tailpiece mounting. Not DOT approved. NOTE: To be used with stock Stop/Tail Light - NOT intended to be used as replacement. LEDs for Signal/Marker use require LED Flash Controller (07-H505R) - Order seperately. Fits all Bikes. |
|
 |
| TARGA INCANDESCENT LICENSE LIGHT - WHITE Item #: 07-4080W |
$38.06
|
INCANDESCENT LICENSE LAMP-POLISHED ALUMINUM HOUSING
This bright light is enclosed in a machined aluminum housing with a 6mm threaded stud allowing it to be mounted to the license plate hole with no drilling. It will light a license plate no matter where the plate is mounted. (Stock location or undertail, rear axle mount or any custom location). We recommend it for use with the Titebike axle mount relocation kit. Sold individually.
Size is 5/8 diameter x 1-3/4 long.
Not DOT approved.
Fits: ALL BIKES |
|
 |
| TARGA LED LICENSE LIGHT - WHITE Item #: 07-5157W |
$37.35
|
LICENSE PLATE LIGHT-MACHINED ALUMINUM HOUSING-WHITE LED
These Bright White LED lights are housed in a super small machined aluminum body, only 3/10 x 7/10 in size. The LED light is installed at a 90 angle making for an ideal mount on either the undertail or license plate. Requires a 5/16 hole for mounting. Sold individually. Not DOT approved.
Fits: ALL BIKES |
|
 |
| TARGA LICENSE LIGHT WHITE LED- BLACK BODY Item #: 07-4072WBK |
$38.06
|
Our most popular light for custom applications. Featuring a black anodized aluminum body 5/8" long x 5/8" wide with a single bright white LED. LED light is mounted at a 70 degree angle which makes it great for all undertail applications. Ideal for use on Targa undertail cowlings. Installation will require drilling a single 5/16" diameter hole. 12v - 2 wire. Sold individually. Not DOT approved.
Fits: ALL BIKES |
|
|
|
|
|
 |
| Ultra streamline LED license plate light Item #: CY25457 |
$28.88
|
Replaces stock license plate light. Ideal when illiminating rear fender or installing undertail kits. Light is designed to project a bright white beam onto license plate without additional hardware, a simple 1/8" hole will suffice.
Not for use where D.O.T lighting is required |
|
powered by
