|
|
|
|
| Application Chart |
Diagrams |
Application
Notes |
|
| 2001 Suzuki GSX-R 1000 (K1) |
|
|
| 2002 Suzuki GSX-R 1000 (K2) |
|
|
| 2003 Suzuki GSX-R 1000 (K3) |
|
|
| 2004 Suzuki GSX-R 1000 (K4) |
|
|
| 2005 Suzuki GSX-R 1000 (K5) |
|
|
| 2006 Suzuki GSX-R 1000 (K6) |
|
|
| 2007 Suzuki GSX-R 1000 (K7) |
|
|
| 2001 Suzuki GSX-R 600 (K1) |
|
|
| 2002 Suzuki GSX-R 600 (K2) |
|
|
| 2003 Suzuki GSX-R 600 (K3) |
|
|
| 2004 Suzuki GSX-R 600 (K4) |
|
|
| 2005 Suzuki GSX-R 600 (K5) |
|
|
| 2006 Suzuki GSX-R 600 (K6) |
|
|
| 2007 Suzuki GSX-R 600 (K7) |
|
|
| 2001 Suzuki GSX-R 750 (K1) |
|
|
| 2002 Suzuki GSX-R 750 (K2) |
|
|
| 2003 Suzuki GSX-R 750 (K3) |
|
|
| 2004 Suzuki GSX-R 750 (K4) |
|
|
| 2005 Suzuki GSX-R 750 (K5) |
|
|
| 2006 Suzuki GSX-R 750 (K6) |
|
|
| 2007 Suzuki GSX-R 750 (K7) |
|
|
|
|
|
|
|
|
|
|
|
|
|
Kit comes in two pieces
|
|
very easy to install!
|
|
|
This is the TiteBike GSXR license plate mount |
|
This license plate relocation kit is very easy to install. |
|
Simply replace the left side axle spacer with the TiteBike GSXR bracket |
|
Does not require the removal of the axle (if the axle is installed as it comes from the factory) |
|
 |
|
 |
|
Universal license plate bracket has 5/16" license plate holes to accommodate TiteLite license plate lights (you may need to drill the holes in you your license plate itself 5/16" also) |
|
Counter sunk holes on two sides for either vertical or horizontal mounting |
|
|
|
This mount simply replaces the left axle spacer of your Suzuki GSXR(shown here on a 2003 Suzuki GSXR 1000) |
|
The TiteBike Universal license plate mount then bolts on to the axle spacer |
|
Counter sunk holes allow for various mounting positions |
|
 |
|
 |
|
Back side of kit with license plate attached (shown on a 2003 GSXR 1000) |
|
Shown with the TiteLite option |
|
|
|
|
| WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. |
|
| The Q&A on this Product |
|
|
| QUESTION: Will this work on M109R, 2007 ? |
| ANSWER: No, sorry, we do not have an axle mounted solution for that model. |
|
| QUESTION: I have a 2007 Gsxr 600 I can mount this horizontally right? |
| ANSWER: Yes, your choice of horizontal or vertical - the license plate bracket has mounting holes for either position. |
|
| QUESTION: Will this work on a katana 750 2006 model. |
| ANSWER: No, sorry. |
|
| QUESTION: my axle nut is on the right side on my 2007 gsxr1000.do you have for right side? |
| ANSWER: This kit mounts on the left and replaces the left side chain adjuster. We do not have a kit for the right side. |
|
| QUESTION: Will this pass the MD state inspection? |
| ANSWER: We do not have information on MD state requirements. Contact your local DOT. |
|
| QUESTION: tengo uan Harley Davidson modelo Road King y quisiera cambiar la matrícula y ponerla abajo, a la izquierda y sujeta a los tornillos que sujetan la maleta quedando encima, muy cerca del tubo de escape izquierdo ¿Tenéis ese soporte ?
Gracias |
| ANSWER: Hola, lamentablemente, no tenemos un soporte que funcione asi. Usted podria comprar el universal 1t-0099, y adaptarlo para su aplicación. No puedo garantizar que quede perfecto, pero Ud. puede hacerlo que funcione. |
|
| QUESTION: will the plate scrape the ground while cornering? |
| ANSWER: The bracket has several possible positions. If you mount the plate vertically and put it up as high as it will go on the mount, you will be able to lean over as far as possible. |
|
| QUESTION: will this kit fit a 2006 gsxr 1000 with an exotic cycle swingarm extension? |
| ANSWER: If the swingarm extension uses the exact same left side chain adjuster as the stock swingarm, then this part will work perfectly. It will always work where the left side chain adjuster block is stock or exactly the same as stock, as it replaces this part with a high-quality billet part that is capable of mounting a license plate bracket. |
|
| QUESTION: Will this kit fit on a '05 Hayabusa? If not, Do you have a similar kit for the 'busa without the chain guard? |
| ANSWER: We do not have a TiteBike kit for the Hayabusa. |
|
| QUESTION: will this kit work for a 2001 suzuki katana 750???? |
| ANSWER: No, sorry |
|
| QUESTION: Does this also work on the 06 gsxr 600, or is it not our yet |
| ANSWER: This kit will work. |
|
| QUESTION: how about fitment for a 2002 tlr? |
| ANSWER: We do not have one at this time. |
|
| QUESTION: Where do you run the wires from the license plate lights? And can I get an inspection sticker with this setup in MA? |
| ANSWER: If you get the matching TiteLites, you run your wire down under the swingarm. You will need to check with your state specifically as we cannot say about its legality. You can mount the license plate horizontally. We have not heard of any states where we know this is not legal. |
|
|
|
| Ask your question here: |
|
| Your email (so we can send you the answer): |
|
|
|
powered by