10mm SWINGARM SPOOLS\SLIDERS - 1 Step (set of 2)
2 Matching Spools with integral Swingarm Sliders
Item no. 27-3110
Today$37.70
Application Chart Diagrams
Application
2004 Kawasaki ZX 10R
2005 Kawasaki ZX 10R
1993 Kawasaki ZX 6R Ninja
1994 Kawasaki ZX 6R Ninja
1995 Kawasaki ZX 6R Ninja
1996 Kawasaki ZX 6R Ninja
1997 Kawasaki ZX 6R Ninja
1998 Kawasaki ZX 6R Ninja
1999 Kawasaki ZX 6R Ninja
2000 Kawasaki ZX 6R Ninja
2001 Kawasaki ZX 6R Ninja
2002 Kawasaki ZX 6R Ninja
2003 Kawasaki ZX 6R Ninja (636)
2004 Kawasaki ZX 6R Ninja (636)
WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations.
The Q&A on this Product
QUESTION: I can not seem to find any frame slider for a 95 ZX6R on your site, were are they?
ANSWER: These should work on that bike. From what I remember, only 1 side of the spool lugs is inset, so you should need this kit (which has 1 spacer for the inset lug). Check your bike to be sure.
QUESTION: I have a 96 ZX6R. Can these be mounted higher up on the frame like sliders I've seen on other bikes? Or only on the swingarm?
ANSWER: These are for the swingarm...there are frame sliders available for this bike as well.
QUESTION: will these fit a 1996 zx600e
ANSWER: I do not believe that the ZX6E had holes for spools in 1996 - do you see a spot for them welded to the bottom of the swingarm near the axle?
QUESTION: I have a 2006 kawasaki zzr600. Will these fit?
ANSWER: Yes, they will
QUESTION: Will they fit a 1996 ZX6R?
ANSWER: Yes they will, but this item is being discontinued and replaced with 10mm spoll sliders. They are $29.99 and will be available in a week.
QUESTION: I would like a set for my 1990 FZR1000 but I don't see a mount point to install them.
Am I missing something or do these work on the OEM?
ANSWER: If there is a spot, it will be on the bottom of the swingarm just forward of the axle. If there is nothing there - you either need to intall a set or use a pad stand.
QUESTION: How do I order a set for a 2005 ZX12R?
ANSWER: You need to confirm using you judgement, if you need the spools with steps or not. We have new spools for the bikes taking 10mm bolts - they are a spool slider make from black delrin that retails for $29.99....and they will have optional spacers that you can utilize when you need them. They will be avilable on 4/20/06.
QUESTION: would these fit a 95 zx750?
ANSWER: No, I think that the ZX7's use 12mm spools - which we do not make.
QUESTION: what is the "step" and its dimensions?
ANSWER: The "step" is a 1/2 inch spacer. Some bikes need a 1/2 inch spacer on one side, some need the spacer on both sides.
QUESTION: Do all the 10mm spools have a 1.25 thread pitch?
ANSWER: Yes, all bikes that take 10mm spools are 1.25 pitch
QUESTION: The ZR750S has the mounting tabs below the swing arm, however I am not sure if you have a listing yet for the exact size.. Will the 10 mm work with the ZR750S ??
Thanks !
ANSWER: I have not sold them for the KawasakiZR750S, but every recent Kawasaki has taken 10mm spools.
QUESTION: Will these spools fit 2001 ZX-6R?
ANSWER: Yes they will
QUESTION: Hello will these fit a 2005 Z750S
ANSWER: Honestly, we do not know. The part number above has a standard 10mm spool and one 10mm with a step down that fits into the frame.
QUESTION: WILL THESE SPOOLS FIT ON MY 97 KAWASAKI ZX-6R NINJA?
ANSWER: Yes, they will
QUESTION: I have a Kawasaki ZRX1200R... what spools do I need to order?
ANSWER: We have had only a few requests for spools for either the ZRX11/1200. What we did was create a kit 27-1020 which both spools have a 'step'. It's not listed but it is available for $24.99.
QUESTION: will the spool fit 93 kaw. zx11c-4 c-model
ANSWER: We believe the ZX11 would require both spools to have a 'step' or recess to fit inside the frame. You need to check your spool location on the bike and see if that is so. Assuming we are correct you could order 27-1020 for the same price as the SKU noted above and get that set up. If only one side needs the 'step' then the SKU above is correct.
QUESTION: will it fit a 2002 suzuki katana 600
ANSWER: We do not know. Suzuki's as far as we have experienced take 8mm spools. The Katana model is not a race bike which is what we normally test our products on. The 27-1010 spools are 10mm with one spool 'stepped' down to space it out and fit inside a Kawasaki ZX9 frame.
QUESTION: I have a 2005 kawasaki zzr600. Will these fit?
ANSWER:
QUESTION: do they make a kit to mount spools on a 01 katana 600?
ANSWER: No, they do not. You would need to weld a threaded mount to the bottom of the swingarm or use a riv-nut kit.
QUESTION: I have a 1975 Z1 900 Kawasaki and I'd like to use one of these stands that require these spools.I have a aluminun SoCal extended swingarm and was just wondering if just any of these spool sets will work after I tig weld the theaded 3/4"X1" round aluminum stock in place. Would you recomend the 12 mm bolts due to the 550 lb weight of the bike? Thank you
ANSWER: No, 10mm is fine - 8mm would do the trick as well....550 lb is not too out of the ordinary, certainly not enough to think about shearing off an 8mm bolt.
QUESTION: will these fit a 2004 zx-6rr
ANSWER: Yes, they will
QUESTION: Will the spools also fit a 2002 ZX12
ANSWER: Yes, they should fit a ZX12. However, you need to check the bike itself. If the spool "receivers" are both near the outer edge of the swingarm, the regular (27-1000) spools will work. If one is inset more than the other, you need the 27-1010.
QUESTION: Will this fit the 2003 ZX6R 636?
ANSWER: Yes, they will.
QUESTION: Does this fit the 2000 ZX10?
ANSWER: Not sure about the year 2000. It does fit the new 2004 ZX-10R. Check the swingarm where the spools would mount and see if one side has a step or recess. If so, the p/n above will fit. If the step or recess is absent on both sides I believe it would take the standard 10mm spools p/n 27-1000. Jan - Customer Service
QUESTION: Is this the same spool for the ZX10?
ANSWER: Yes, they are the same.
Ask your question here:
Your email (so we can send you the answer):
powered by
