CBR 600RR 2005-2006 FENDER ELIMINATOR KIT
Kit comes with flush mount turn signals with clear lenses.
This item usually takes about 1 to 2 days to ship
Item no. 1H606
Retail: $149.95(PLUS shipping)
Today$141.95
Application Chart Diagrams
Application
2005 Honda CBR 600 RR
2006 Honda CBR 600 RR
WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations.
The Q&A on this Product
QUESTION: hello
ANSWER: hi
QUESTION: what colar
ANSWER: stainless
QUESTION: do i need a license light
ANSWER: Comes with this kit
QUESTION: is it street legal
ANSWER: check with your local DMV
QUESTION: how much is shipping to zip 98281, point roberts, washington state?
or
how much is shipping to vancouver, bc, canada?
ANSWER:
QUESTION: Is the fender eliminator fit with plate from quebec?
ANSWER: designed for a 4"x7" plate.
QUESTION: Will the license plate be hittin when you do wheelies or have two peoples on doin wheelies? Or hittin good size bumps?
ANSWER: it de signed to pivot as needed
QUESTION: Do fender eliminators serve a purpose or are they just to upgrade appearance?
ANSWER: Does plastic surgery serve a purpose?......... As with plastic surgery these kit will improve the appearence. Giving the rider a much better feeling about the bike. Thus, more confidence!
QUESTION: where does a led flasher relay connect,on a 2006 honda cbr 600?
ANSWER: contact your honda dealer
QUESTION: I installed the fender eleminator kit and followed the instructions completly on my 06 cbr 600. Now my brake light and front gauges wont work. I checked the fuses and they are fine. Do you know what the problem is?
ANSWER: It's either a fuse..... or you swapped out front signals as well.... If you did this, you'll likely need a new flasher relay or more resistance in that cicuit.... But most likely... It's a hidden fuse.
QUESTION: Is this kit only for the rear signals? Or does it come with front and rear flush mount signals?
Also I plan on getting the New Jardine RT-1 Dual Exhaust is it going to be a problem with this kit?
Thanks....
ANSWER: It will work fine with jardine.......yes, it comes with flush mounts as shown in the photo
QUESTION: When will the new 2007 Honda CBR600RR Fender Eliminator kit be available? What is its number?
ANSWER: 1H607.......around the end of March....
QUESTION: Will this fit my 2007 CBR 600RR?
ANSWER: no
QUESTION: my plate light burned out. is there any way i can order just the same light?
ANSWER: Call or contact Competition Werkes
QUESTION: Can i purchase only the plate holder, light and hardware kit? And do you ship in Canada? What whould be the cost of this purchase and shipping.
ANSWER: Can not seperate the kit.
QUESTION: I have an 05 CBR 600RR and I'm interested in purchasing this product. However, it seems as though there are several customers who have had problems with the lights. Is it "operator headspace" or is there a design problem with the turn signals? Call comp werkes? Who or what is this?
ANSWER: There are very few problems with the lights verses quanities sold. Competition Werkes, manufactures these kits. 1tail.com retails them.
QUESTION: How far back is the lisence plate bracket? doe it sit over the hugger?
ANSWER: yes over the hugger
QUESTION: I would like to know if this product is street legal in california and also if this product comes with directions for install (and how good of instructions they are) please. Thank You
ANSWER: You MUST check local laws. Instructions are good and Comp Werkes has a very helpful tech dept on call.
QUESTION: im looking to buy the kit but i would like to know if you have to use the turns signal that it includes and can you not install them and use the tail light with the integrated signals
ANSWER: signals do not have to be installed
QUESTION: I just installed this kit on 600rr and can,t seem to get lic tag light to work.why???
ANSWER: call comp werkes
QUESTION: does it matter what exhaust you have for this kit. do you half to have the default exhaust?
ANSWER: shouldn't matter
QUESTION: hi do u sell thelicense plate led separate. my led from the kit i bought stop work. 1h606. please give me a price and availability
ANSWER: contact comp werkes its under warrantee
QUESTION: Do you have this item in stock? How long does it take to ship to florida?
ANSWER: yes....a week
QUESTION: Will this Kit work on a 2006 cbr1000?
ANSWER: NO
QUESTION: my plate led keeps on blinking all the wires are fine but 3 out of 6 led's only work but blinking. can i buy the same light separate?
ANSWER: Call Comp Werkes
QUESTION: you have to drill 3 holes, got it. But where do you have to drill them? And if I click the little box that says "matching front signal kit 4" would I get flush signals or not? also, do they constently stay on when the bike is running? or do they only flash when I signal?
ANSWER: Three holes drill in the battery box. Front signals are shorts stalks with a running light.
QUESTION: So the front flush blinkers wont be in until Feb 07'? And where/how much drilling is involved for the 06' CBR600RR?
ANSWER: front signals avail from comp werkes. you must drill 3 holes with this kit.
QUESTION: i have a yoshimura rs5 will it work with this kit? Are the front turn signals flushed?does the lsignal lights use LED?
ANSWER: will work with yosh.....doesn't come with front signals.......rear signals are not LED.
QUESTION: I have an 03 600rr but do not like the kit for it. will the 05 kit fit on the 03
ANSWER: no........
QUESTION: Is this kit hard to install? can i do it my self? does it work with stock or an aftermarket pipe?
ANSWER: Should take about an hour..... designed to to yourself with normal hand tools... Works with MOST exhaust, as long as they're routed close to stock.
QUESTION: I just ordered. I have flush mounts (hot bodies) on the front and my rear and front signals flash fast. Will the rear signals with this kit flash fast also? I bought in line resistors. They are 22 ohms and 1/2 watt. Does the wattage matter?
ANSWER: they will still flash fast.... you need to change your flasher relay.
QUESTION: All i need is the license plate mount that is fastened to the forward part of the stock under panel near the rear shock. Can i order this sperately? I so what is the price?
ANSWER: contact comp werkes
QUESTION: are the lights LED???
ANSWER: lic light LED.......signal not
QUESTION: I have a arkopvic exhaust will the kit be compatible?
ANSWER: yes
QUESTION: Will this fit the 2006 models
ANSWER: yes
QUESTION: Is there a light for the license plate?
Will this item be coming down in price?
ANSWER: yes there's a light........No we sell them all day long at this price.
QUESTION: Is the optional matching front signal kit 4 flush with the farrings or do the turning signals stick out?
ANSWER: they stick out.......short stalks
QUESTION: Do you have any pics of the matching fronts?
ANSWER: go to compwerkes.com
QUESTION: i have a 05 cbr 600rr and would like to know how hard it is to install the fender eliminator kit and the front flush mounts.
ANSWER: Give yourself an hour and a half
QUESTION: do you have the new flush mounts for the front yet?
ANSWER: The should be in the middle of this week.
QUESTION: I have a lowered '05 600RR, will this kit still work or will it touch the hugger even when parked?
ANSWER: it'll touch.
QUESTION: I replaced my front turn signals already. Can I attached the resistors to my rear turn signals? It was such a pain to replace the front signals.
ANSWER: yes, anywhere in the circuit.
QUESTION: I replaced my front turn signals already. Where do the resistors go, front turn signal or the rear turn signals?
ANSWER: Resisters can go anywhere within the circuit.
QUESTION: If I want JUST the license plate bracket...(no turn signals) whats the cost? And can I get it in black NOT chrome/billet?
ANSWER: contact comp werkes
QUESTION: Are there any aftermarket accessories that you know for sure will not work if using this fender eliminator?
ANSWER: It's not compatable with any plastic undertails
QUESTION: how visible are the turn signals from directly behind? they look like they are only visible from the side.
ANSWER: very visable
QUESTION: the front flush mounts due in feb from comp werkes...they will work fine, as in, no fast blinking, with this kit?
ANSWER: They will also be sold with a flasher relay, which will set all signals to a standard speed
QUESTION: does this kit come with plate light
ANSWER: Yes LED lic light.
QUESTION: hello im ready to purchase this product is there any pre wiring cables i need to buy or anything extra i need to purchase and what kind of front lights do you guys recommend
ANSWER: It's a complete kit. I'd wait for Comp Werkes new flush mounts due in Feb.
QUESTION: What part of the plastic do you have to drill holes in on the 05'cbr rr?
ANSWER: bottom of the battery box
QUESTION: I ORDERED THIS PRODUCT, AND ALSO FRT. CLEAR TURN SIGNAL REPLACEMENTS. HAVE NOT GOT YET. DO THE WIRRING HARNESSES PLUG IN TO FACTORY CONNECTIONS, OR DO TOU HAVE TO SLICE WIRES. IF SO ON YHE SPLICE IS THE WIRES JUST IN SERIES FROM FLASHER BEING BOTH HOT.AND HOW MANY RESISTORS WILL YOU NEED AND WHERE DO THE GO FRT. OR BACK LIGHTS OR ALL. THANK
ANSWER: Call comp werkes
QUESTION: Will this FE work with the new 2006 CBR 600 RR? If not, do you have one that will?
ANSWER: yes it will
QUESTION: does this kit void the warrenty on a new o5 cbr 600rr
ANSWER: Ask Honda. It shouldn't
QUESTION: Can you post the instructions on mounting the fender eleminator.
ANSWER: No, against policy
QUESTION: one more question, what black plactic part do we need to drill for the 05 cbr600 rr?
ANSWER: Yes, you'll need to drill two 1/4" holes in the black plastic.
QUESTION: the pivot mount for the lic plate, does it stay in one spot until u hit a bump or can i set it in a position and it stay there (wont fall back down)?
ANSWER: It Pivots (moves back and forth as nessesary). It is not designed to be set in a fixed position.
QUESTION: I have the YOSH RS-5 installed on my bike currently, will the heat from the pipe melt the turn signals?
ANSWER: not if the heatshield is on.
QUESTION: ready to buy...will this product's turn signals function correctly with aftermarket front turn signals...and will they flash fast like my front after market turn signals?
ANSWER: If your fronts are flashing fast so will the back. Try putting an in line resister in. Radio Shack about 20-25 ohm's per side.
QUESTION: where is the flush mount turn signal located? I was looking at the pic but cant see it
ANSWER: look next to the exhaust.
QUESTION: Do you know for sure the signals will flash normal? Your answer above seems like you have not tested it. I would hate to buy it and find out that it dosent work correctly. 20% restocking is a no-go for me.
ANSWER: It flashes fine with stock fronts. If you change fronts as well you'll PROBABLY need to get some in line resisters (Radio Shack)
QUESTION: is the resistance set to make the turn signals flash both at normal speed or are they flashing faster on one side?
ANSWER: They should flash normal.
QUESTION: is there any way that the lic. plate bracket will hit the rear fender or the tires whenever u hit a bump coz its kinda close???
ANSWER: It's designed to come in contact with the hugger and then pivot up out of the way.
QUESTION: what is your return/exchange policy? i have a `05 600rr, ordered a fender eliminator on ebay but disappointed with the product.thanks!
ANSWER: There`s a 20% restock fee, but if you got it on eBay, then you have to deal with the person that sold it to you.
QUESTION: is it a bummer to install?
ANSWER: It's simple
QUESTION: Bought the kit, love it! looks great, thanks !! Do you always do this good of buisness
ANSWER: With products like Comp Werkes. Yes!
QUESTION: Does the CBR600RR '05 Fender Eliminator Kit comes with a front flush mount turn signals too?
ANSWER: in the rear yes. See PHOTO
QUESTION: will the plate be in the way of the rear wheel when hitting a bump on the road?
ANSWER: No, that's why it's on a PIVOT
QUESTION: Is there any drilling involved with installation?
ANSWER: Yes, but only to black plastic.
QUESTION: does this kit work on 2005 600RR?
ANSWER: Yes
QUESTION: Do you rear facing picture?
ANSWER: NO
QUESTION: what exactly does it comes with? does it come with a plate mount too?
ANSWER: Main pan, Lic pan, Signal bracs, signals, lic light, hardware, instructions
QUESTION: What does the plate bracket mount to? Is it completely street legal to have your plate mounted back into the rear fender?
ANSWER: These kits are NOT DOT approved. But are legal in most area's (check your local laws) This kit is mounted to the battery box and backed with some support brackets.
QUESTION: The flush mounted lights are not just screwed to the fender are they???There is hardware and brackets like the 04 kits????Sorry for all the questions, ready to buy.
ANSWER: Flush mounts, mount to new brackets
QUESTION: Also, I have the Micron Dual Outlet pipe on already, will this kit fit????
ANSWER: as far as we know
QUESTION: I need some kind of matching front signal lights, I know you don't offer the flush mounts, what do you recommend???? Are they still $30 extra like in 04???Thanks
ANSWER: yes,same front kit as last years
QUESTION: Is there a Comp. Werkes FE kit available with no turn signals? (I would still like to have the lic. light.) For an '05 600RR.
ANSWER: no
QUESTION: I ordered the CBR600RR '05 Fender Eliminator Kit and I want to know if you sell matching flush-mount signals for the front? If so, what is the Item #? If not, what do you recommend to match the rear signals?
ANSWER: no flush mounts
QUESTION: When you say the signals are clear are you talking about the covers? Is the light bulb yellow? Also, do you sell matching signals for the front?
ANSWER: clear with a amber bulb.
QUESTION: Can you get them with amber turn signals?
ANSWER: Comes boxed with clear signals.
QUESTION: is this kit for stock exhaust or aftermarket exhaust? post pictures so we can see the finished look
ANSWER: Fits both. Looks very similar to the 03-04
QUESTION: Are the flush mount turn signals for the front signals or for the rear?
ANSWER: rear.
QUESTION: when are you going to post pictures because i am ready to buy this if i looks exactly as the 2004 model
ANSWER: Looks very similar. The main difference is we were able to tuck the signals in much more. Lic plate mounts on the same principle.
QUESTION: Is this the 2005 Fender Eleminator or is a "tail kit" something diff.
ANSWER: This is a rear fender eliminatkor that gets rid of the black plastic hanging down fender. It consists of a license plate mount that is fastened to the forward part of the stock under panel near the rear shock. It includes short stalk type signal lights and a license light.
Ask your question here:
Your email (so we can send you the answer):
powered by seo company
