YZF R6 2006 -2007 LTD Fender Eliminator Kit
All Stainless Steel. Includes rear signals and LED license plate light.
This item usually takes about 1 to 2 days to ship
Item no. 1Y607LTD
Retail: $149.95(PLUS shipping)
Today$147.88
Application Chart Diagrams
Application
2006 Yamaha YZF R6
2007 Yamaha YZF R6
WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations.
The Q&A on this Product
QUESTION: do you guys sell the UnderTail cover part on its on? I'm refering to a square 6.5 cm by 6.5 cm which covers the hole where the original undertail was attached to.
ANSWER: no
QUESTION: Any reason this would be illegal or a possible ticket from an officer? any advice or knowlegde on that? I mean it seems pretty visible. Thanks
ANSWER: its always up to the officer.....good luck
QUESTION: Can you adjust (tilt up or down) the angle of the license plate once the kit is mounted?
ANSWER: no
QUESTION: will this item fit the 2008 r6. if not, is there something similar to it?
ANSWER: NO.... you need the 1Y608LTD
QUESTION: I'm planning on getting an R1, do you think I would be able to swap from my 07 R6 to an 08 R1?
ANSWER:
QUESTION: I see that someone has already asked the question if this product is available for an '08 R6. I do not know when that message was posted. Is it now available for an '08 R6? If not, do you know how long it will be before Comp Werkes releases this information? Thanks
ANSWER: Should be available by April 5th
QUESTION: Do the turn signal bracket welded together with the licensed plate bracket? Cause i don't need the turn signal.
ANSWER: they're on a seperate bracket... that can be left off
QUESTION: Just wondering if this item with bolt right on to a 08 R6. If not, are you going to be coming out with a 08 Eliminator kit?
ANSWER: Comp Werkes has not found an 08 R6 to check on yet.
QUESTION: what about the stock holes , does the kit have a piece to cover the stock holes, or they will just be left open???
ANSWER: Comes with a cover and a plug.
QUESTION: do you use the stock center bolt on the plate mount? because I have the 07 and that allen is too short to reach?
ANSWER: Contact Comp Werkes
QUESTION: were dose it screw on to the fender is there a hole all readly
ANSWER: Uses the stock bolt for the hugger fender
QUESTION: Is the brake light in the middle of the lens?What color are the signals?
ANSWER: This is the stock brake light...... signals are clear with amber bulbs
QUESTION: Hi.....
I am planning on purchasing this product (2006 -2007 Yamaha YZF R6 LTD Fender Eliminator Kit.....), and I just wanted the instruction sent to before i make the purchase so i can see if i am able to do it myself........ Item no. 1Y607LTD thnx....
ANSWER: contact comp werkes
QUESTION: Any return policy for international orders?
ANSWER:
QUESTION: does it come with a license plate light
ANSWER: read the discription........ YES
QUESTION: Is there any filling required?
ANSWER: No major mods required
QUESTION: will this fit 07 r6?
ANSWER: yes
QUESTION: Will you ship to Canada?
ANSWER: Yes, we ship to Canada. The cost of the international shipping will be charged to your credit card as a second transaction.
QUESTION: Will this kit fit the 2006 YZF-R6?
ANSWER: As long as it is not an "S" model
QUESTION: Is it possible to order this item with only the Plate mount with no signals? And would the cost be the same if this was possible?
ANSWER: Sorry we can not break into the kit.
QUESTION: Dow you ship to Chile, South Amercia?
ANSWER:
QUESTION: I am interested in purchasing this product but as i was performing the checkout, I was wondering how you will know what colour my bike is to send the matching cover plate from where the old plate bracket was mounted?
ANSWER: Thgis kit is stainless..... not painted
QUESTION: is there any drilling or glueing involved or is it all screws and bolts?
ANSWER: Its a bolt on kit..... you will need to splice a few wires.
QUESTION: Do you have to use the turn signals that come with the kit? I plan on getting an integrated st&t for my 06 r6. Also, does it pivot if I hit a bump, or if someone else is riding on the back? - I dont want to bend my plate
ANSWER: Just don't install the signals. This kit pivots so no damage will occur, thats the reason for the pivot.
QUESTION: I have a 2007 YZF-R6S. Do you have a fender eliminator kit for it?
ANSWER: The 2007 YZF-R6S is the same as the 04-05 YZF-R6....... Select item# 1Y605 for this bike.
QUESTION: does this work well with my lowered r6? would i have any problems with this product?
ANSWER: The plate would not be visible
QUESTION: On the 1Y607LTD, do you have to rerun wires and cut and splice? Would I be able to ever go back to the stock fender?
ANSWER: You can go back to stock....you'd just need to re-tap the wires.
QUESTION: do thay sell the cover plate seperete
ANSWER: no
QUESTION: can u explain how to connect the wires together?,from turn signals to the license light and back to the stock wires. and a diagram on how to mount the kit under the sit.thanks!
ANSWER: Kit mounts to swingarm..... Wires run through a conduit up into storage area.
QUESTION: Do you sell this Fender Eliminator with the spring loaded plate holder without the turnsignals? If so, how much?
ANSWER: Call Comp Werkes for special orders
QUESTION: LED license plate light do not work any more...what i should do(wires connected well)????
ANSWER: Call Comp Werkes they'll take care of you.....
QUESTION: Do I see a matching cap (so to speak) that covers the place where the original nount is under the tail? It is somewhat tacky to have those holes hanging out.
ANSWER: coes with plug and cover plate
QUESTION: Do u send an instructions with the product when i purchase it?
ANSWER: yes
QUESTION: Are the turn signals amber?
ANSWER: clear
QUESTION: I hav a UK R6, '06. Will the 1Y607LTD fit without any mods? Wot r ur shipping chrgs 2 UK or do u hav a UK supplier? thanx
ANSWER: UK plate probable won't fit........it's designed for a 4" X 7" plate.
QUESTION: Do you know where i can get a retractable fender eliminator for the R6 06?
ANSWER: Not if your looking for a flip plate. Look in the back of a magazine.
QUESTION: I am installing an integrated tail light wiht turn signals, and this is the only eliminator kit i found that i like in that area of the bike, so I do not need the turn signals. If I dont install them on there will there be funny looking parts on the kit because I am not using the turn signals?
ANSWER: Just leave the signal bracket off
QUESTION: Is this product easy to install yourself, or do you recommend having it professionaly installed?
ANSWER: It's pretty basic.... I'd do it at home
QUESTION: will this kit work with the 04 r6
ANSWER: no
QUESTION: Will this eliminator fit on the 50th anniversary r6? Also, do you have any exhaust for this bike?
ANSWER: fender kit....... yes
QUESTION: I would like to have a diagram and instructions sent to me before installation, if at all possible.
ANSWER: contact comp werkes
QUESTION: where to the wires come from for the blinkers? theres no hole in the undertail at this location, plus you have it mounted from the bottom.
ANSWER: Wire runs through a supplied conduit. from the battery box down the brake lines to the plate light.
QUESTION: Do you ship to Canada?
ANSWER: yes
QUESTION: Sorry to be a pest but do u have a picture or diagram of the installation as
I would like to see how it fits before i purchase as I am based in the UK
Regards
Daniel
ANSWER: my tech is on vacation, if you would send this e-mail again monday he'll be back and should be able to e-mail that info, if not we can mail it. thanks.
QUESTION: Where do u mount the licence plate holder to the bike. The instructions that have been sent to me do not have any diagrams on how to mount the fender eliminator Kit. Would it be possible to have a diagram of how to mount the fender sent to me
Regards
Daniel
ANSWER: it mounts between the swing arm and the hugger fender using the single center bolt.
QUESTION: Are there any mods to the body when installing 1Y607LTD? Is there a license plate light on the 1Y607 model?
ANSWER: no modifications and yes it does come with an led license light.
Ask your question here:
Your email (so we can send you the answer):
powered by
