CBR 600RR Fender Eliminator Kit '03-'04
For 2003-2004 Honda 600RR.
This item usually takes about 1 to 2 days to ship
Item no. 1H605
Retail: $159.95(PLUS shipping)
Today$151.95
Application Chart Diagrams
Application
2003 Honda CBR 600 RR
2004 Honda CBR 600 RR
WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations.
The Q&A on this Product
QUESTION: same here i have an 03 600rr and i am going to get integrated turn signals so can i just get the plate mount??
ANSWER: no
QUESTION: hey man, i have a 2003 honda cbr 600rr and all i need is the license plate mounting bracket by its self. do you sale just the bracket? and if not do you know where i could find just a mounting bracket? i just dont want to spend 150 plus shipping and handeling for a bracket. thanks!
ANSWER:
QUESTION: does this kit hold my battery under the driver seat?
ANSWER: Battery area stays in tact
QUESTION: Hi, could you please answer a couple of questions regarding this item? 1) Does this eliminator have a number plate led or light above it? 2) Could you advise on the biggest size plate that could be attached to the plate? 3) As I live in the UK where, should the plate be of a certain size? Do you know whether it would be feasible for over here? Thanks very much.
ANSWER: yes.....no taller than 4 inches
QUESTION: I purchased this item recently. I'm trying to get matching turn signals for the front. Please advice. Thanks.
ANSWER: short stalk III
QUESTION: I see the picture is a stock pipe, I have a Yoshi Rs-5, will this work still?
ANSWER: yes
QUESTION: do you have a kit for the 2007 cbr 600rr yet?
ANSWER: Should be avail April 20th
QUESTION: can you order just the license plate holder and not the lights. I have integrated tail light, so no need for the blinkers.
ANSWER: contact comp werkes
QUESTION: How bright are the turn signals that come with this kit compared to the stock signals? As bright, brighter than stock, etc?
ANSWER: close to as bright
QUESTION: will this bracket pivot enough so my plate does not rub my rear tire while riding wheelies?
ANSWER: yes it will not come in contact with your tire
QUESTION: I have the moriwaki exhaust on my '04 600RR will this kit mount?
ANSWER: ??????????????????able
QUESTION: Will this work Laser Extreme dual exhaust system?
ANSWER: Sorry...don't know.
QUESTION: do you sell the bracket only.
ANSWER: no
QUESTION: are the rear signals that the kit comes with the one on the picture... if so can we change them for short stalks 2 and matching ones for the fronts.. and if they are the exact replacements so no mods needed?? thanks
ANSWER: special requests must go through Competition Werkes
QUESTION: look, this would be my first time even working on a bike, I have a 600RR 04' and I wanted the matching front turn signals, what kit should I even be looking at?
ANSWER: what do you want them to match? the stock rear? or do you have different signals on the back.
QUESTION: will this kit work with a arata SLIP-ON on a 04 600rr
ANSWER: Yes.
QUESTION: 2006 honda cbr600rr will fit?
ANSWER: 1H606 sameas the 05
QUESTION: how much will the liscence plate kit cost without the turn signals?
ANSWER: Thats only available from Comp Werkes...
QUESTION: Is this kit will work with Jardine slip on? I am not sure if they uses normal form or not.
ANSWER: yes it should
QUESTION: What are the state laws on license plate mounting for motorcycles and were can i find them
ANSWER: Check with your state's DMV every state is slightly different
QUESTION: I need to know if the 2003-2004 cbr600rr fender eliminator (item no. 1H605) will leave a mark on the hugger from the rollers on the license plate mount? Thanks for your help.
ANSWER: If you don't keep it clean YES. I suggest a replacable strip of clear protective tape.
QUESTION: do you have the comp. werkes kit for 03' 600rr in stalk. please e-mail me asap.
ANSWER: It would ship directly from Competition Werkes
QUESTION: have cbr600rr fender elimination kit 2003, lost instructions. could you send a set. thank you.
ANSWER: Call Comp Werkes
QUESTION: i purchased the kit for the 2005 cbr 1000rr, with after market (yoshi rs-5 pips. it does not fit. i was looking for this one on the 600rr with the whole under piece with the plate mounted just a little to the left. is there one just like this for my 1000rr? thanks.
ANSWER: The kit for the 05 600rr will work. (1H606)
QUESTION: I read on the 600RR website that Competition Werkes had a Fender Eliminator for the D and D Dual exhaust. Is this accurate?
ANSWER: Yes, but you must buy directly from Competition Werkes as they are a special request item, and are made one at a time.
QUESTION: My bulb is out on for the 04 600rr fender eliminator what kind of bulb do i need to replace it with?
ANSWER: Take the bulb to an auto parts store and cross reference it.
QUESTION: Is the kit for the 2005 CBR600RR available yet? Please send info to 1tail.com right away.
ANSWER: Part# 1H606 Retail $149.95 avail. 3-3-05 no photo's yet.
QUESTION: will i get pulled over in california because of the position of the license plate?
ANSWER: Depends on the policeman. You need to check your local laws.
QUESTION: Will this fit the 2005 600RR
ANSWER: No, we're getting a bike for proto-typing 2-18-05. Fender Eliminator will be available about two weeks later.
QUESTION: The 600rr is my first bike and I'm not too mechanically savvy with it yet. Is the installation of this kit very involved? Meaning, will I be required to cut, drill, remove parts of my bike? Please let me know if the directions are fairly user-friendly and if a newbie will have any problems installing. Thanks in advance!
ANSWER: The hardest part is the bodywork removal/reinstall, not that it's hard, but a "newbie" will be afraid of it. Ya, have to learn somewhere, might as well be on the trickest kit on the market.
QUESTION: Will this kit work with a FULL exhaust system purchased from Arata?
ANSWER: Sorry Arata does NOT use a normal routing of the mid pipe. Our kit will not work in normal form. Some guys have modified our kit (removed lic light, and dropped kit 1/4") and made it work. check out 600rr.net
QUESTION: Do you provide shipping to Sydney, Australia
ANSWER:
QUESTION: Do you sell matching front turn signals
ANSWER: Front signal kit runs $29.95
QUESTION: so this kit will fit a 2004 600rr?? the turn signals that come with it, are they the exact ones, same size & clear lens, and everythin as shown in the first picture above?? http://www.1tail.com/cartimages/m/15304.JPG
ANSWER: Same bike, same kit!
QUESTION: will this rub on the rear tire hugger when the suspension is compressed?
ANSWER: It has a roller on the bottom ,which rolls down the hugger as needed.
QUESTION: i put a arata slip on exhaust and the light for the licence plate does not fit
ANSWER: Thats be because Arata doesn't run their exhaust in the stock location. You'll need to find a flush mounted lic light.
QUESTION: I'm looking @ getting the matching frt turn signals also are just as easy to insatall and will I have any big gapping holes where stock ones were/ Also are both the frt and rear legal??
ANSWER: No, aftermarket turn signals are DOT approved. They are highly visible and should not be a problem. There will be no gaps if you purchase the front signal mounting kit.
QUESTION: Do you sell the short stalk III kit for the frt turn signals ?? And how much are they?
ANSWER: Yes,check price w/ 1tail
QUESTION: Hello, I want to buy this fender eliminator kit for my '04 600RR. What style are the turn signals? I want to buy matching short stalk turn signals for the front as well.
ANSWER: Short stalk III, you'll need to get a front mounting kit asa well.
QUESTION: Am i going to be able to put this on myself, if so, how long?
ANSWER: YES, It takes most guys about 2 hrs.
QUESTION: how long for shipping?
ANSWER: can go out today
QUESTION: does this kit re-locate the seat lock keyhole? are the wire connectors compatible with the factory connectors? are the turn signals led or incandescent? thank you
ANSWER: The lock is not affected. We use crimp-on butt connectors. The lights are not LED.
QUESTION: does this kit have a tag light? and if not,can one be attached?
ANSWER: This kit come w/ a new lic light.
QUESTION: Do you need to drill or cut the rear cowl to attach this?
ANSWER: No, mods nessesary. We do recommend drilling one hole in the black plastic only, for wiring, but its not an absolute nessesity.
QUESTION: can i buy it with out the turns signals and how much would it be?
ANSWER: Only through Competition Werkes.
QUESTION: Hi, will this kit work with an aftermarket exhaust pipe such as Two Brothers or Devil?
ANSWER: It will work w/ any single canister up the middle exhaust. Not any dual canister or side mounted exhaust.
Ask your question here:
Your email (so we can send you the answer):
powered by
