EX250 Fender Eliminator Kit '88-'07
Fits 1988 through 2007 EX250
This item usually takes about 1 to 2 days to ship
Item no. 1K251
Retail: $109.95(PLUS shipping)
Today$101.95
Application Chart Diagrams
Application
2006 Kawasaki EX 250R Ninja
2007 Kawasaki EX 250R Ninja
1988 Kawasaki EX 250R Ninja F 2
1989 Kawasaki EX 250R Ninja F 3
1990 Kawasaki EX 250R Ninja F 4
1991 Kawasaki EX 250R Ninja F 5
1992 Kawasaki EX 250R Ninja F 6
1993 Kawasaki EX 250R Ninja F 7
1994 Kawasaki EX 250R Ninja F 8
1995 Kawasaki EX 250R Ninja F 9
1996 Kawasaki EX 250R Ninja F10
1997 Kawasaki EX 250R Ninja F11
1998 Kawasaki EX 250R Ninja F12
1999 Kawasaki EX 250R Ninja F13
2000 Kawasaki EX 250R Ninja F14
2001 Kawasaki EX 250R Ninja F15
2002 Kawasaki EX 250R Ninja F16
2003 Kawasaki EX 250R Ninja F17
2004 Kawasaki EX 250R Ninja F18
2005 Kawasaki EX 250R Ninja F19
WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations.
The Q&A on this Product
QUESTION: will it fit 88 ex 250?
ANSWER: yes
QUESTION: So, you take out the entire fender, which runs all the way to the front of the back tire.. and replace it with something that only runs 12 inches in front of the tail lights? Is it not a problem to have the rest of the underside of the bike open to dirt, water and mud? If I just cut the visible part of the fender off but leave the rest of the wheel well protection in place, can i still mount this kit?
ANSWER: You do NOT remove the entire undertray....... You remove the back half! from the seam back... and replace it with this kit.
QUESTION: What about the license plate light, where do I mount that? I don't see how you could from the pics.
ANSWER: You get your light from the bottom of the tail light... clear lense is included
QUESTION: Do you sell just the clear plexi lense for the break light tag ilumination?
ANSWER: no.... you might contact comp werkes
QUESTION: will it fit 05 250 ninja
ANSWER: yes
QUESTION: Would you have an undertail kit (fender eliminator) for a 2008 Kawasaki Ninja 250R?
ANSWER: Yes part # 1K252
QUESTION: do you send the eliminator to australia ?
Will it fit 2007 model gpx250 (ex250)
ANSWER:
QUESTION: Does this kit come with the liscence plate mount?
ANSWER: yes
QUESTION: Got the kit in yesterday. Install was fine, except 07 model does not have bolts in the stock turn signals. threfore, it is not exact bolt on bolt off. Stock turn signals have a compression clip, and tiny phillips head screw. However, a hacksaw blade and locktite will make the stock blinkers work. Still a nice kit, I like it.
ANSWER: Thanks for the input.
QUESTION: Is this kit legal in the sate of Illinois?
ANSWER: Good ? don't know
QUESTION: will it fit the el250 eliminator
ANSWER: yes
QUESTION: Whats the difference between the ex250r and the ex250f? I have a 2006 EX250F and was wondering if it would still fit. Thanks.
ANSWER: None.... the newer models do have a different turnsignals which do not fit the mounts as well as the early models....
QUESTION: If I understand it right, removing the fender will leave a big hole under my seat, so will this kit still protect the bottom part from muds entering it? Or will I need to clean up alot of dirt from under my seat when I use this kit?
ANSWER: It protects it pretty well..... But, its NOT water tight.
QUESTION: Will this work for the 2007 Ninja 250 EX?
ANSWER: yes
QUESTION: does it fit an 2007 ex250r
ANSWER: As far as we know
QUESTION: how well dose the metal blend in to the plastic underneth, im mean is there (no) gap what so ever. and how well is it built
ANSWER: There is a gap.....but its NOT visible and does not effect storage ability.
QUESTION: if it dont fit do i get my money back minus the shipping
ANSWER: If you have a EX250....it'll fit.
QUESTION: to whom it may concern i noticed you sale the fender eliminator kits for an ex 250 i was wandering if you sold flush mount blinkers also my sons bike is an ex250 kawasaki ninja
ANSWER: Check w/ comp werkes
QUESTION: How does the license plate illumination work? What work would need to be done for the license plate illumination?
Is there any way to get a copy of the instructions or a link to the PDF Version so I can get a better idea of how the install would go?
Do you have any pictures of your kit off of the bike?
ANSWER: Use light from the bottom of the tail light......new plexi lens supplied. no instructions or photos available
QUESTION: is this DOT aproved for the license plate illumination, as well as placement for the blinkers?
ANSWER: No, they have not went through an approval process.
QUESTION: So you guys are positive this will fit a 2006 EX 250 R
ANSWER: positive is a strong word, were sure in that no changes have been listed for 06 that we're aware of, we wouldn't hesitate to sell it to one of our customers.
QUESTION: I was wondering if there was a Fender Eliminator Kit made yet for the Kowasaki Ninja EX250R 2006 or if you new when it might be available.
ANSWER: It's the same.
QUESTION: will this kit fit an 06 EX 250 R ???
ANSWER: should
QUESTION: I would like to get one of the kits for the Kawasaki 250. What metal is used to make the kit, and does paint stick to it? I would want to paint it black.
ANSWER: It's stainless steel. It would need to be cleaned and primed.
QUESTION: does this kit take any extra drillin
ANSWER: no. bolt off, bolt on.
QUESTION: I found to taillight/turnsignal sockets that fit the two open hole in OEM taillight. can the turn signal mounting points be removed from this item?
ANSWER: yes
QUESTION: can i put universal flush mount turn signals on here? thanks
ANSWER: yes, I believe the flush mount I's will work.
QUESTION: does it have a place for the license plate light? or does it come with it? or.. ? thank you very much
ANSWER: It comes with a clear plastic window, which takes light off the bottom of the tail light.
QUESTION: is it hard to install, what it the estimated time of installing it
ANSWER: Give yourself 2 hours.
QUESTION: I have an 05 it will stil fit that right, I believe it will?
mike
ANSWER: yes
QUESTION: Does the kit come with new blinkers inside those covers, or do you have to pry your old ones out and put them into the new ones.
Mike
ANSWER: This kit doesn't come with signals.
QUESTION: Hey, I know this is where you ask questions, but wanted to tell you that I just ordered it and you have been a great help, thanks!
ANSWER: We try.
QUESTION: OK! my bike just got here, "through shipping", and my finger is on the "buy" button, reassure me one more time that there is no rewiring or anything like that...I just don't see how there can't be, cause the blinkers have to connect somehow to the switch, right?...I trust you guys, you know a lot more about bikes than I do! I will buy the moment I get the response, I promise!, Thanks again guys!...
ANSWER: The signals have a dissconnect built in line. You will simply unplug your wires. Mount the kit. Then plug your wires back in.
QUESTION: does an instruction manual(or something like that) come with this, explaining how to take off the old fender and put on the new one?
ANSWER: Yes, It comes w/ instructions. And there's always our Tech Support to answer any additional questions you may have.
QUESTION: I already emailed ya'll once, thanks for your quick response...I'm on the very edge of buying this...you said in the last email that all that was needed was to unbolt the stock fender and put this onto it...so the rear "blinkers" just stay in place when the stock bumper is taken off?...my fear was that the blinkers were completely connected to that old, fat, stock bumper and would release when the fender was taken off, but is that not so?...thanks again, any help would be greatly appreciated...-Brian
ANSWER: The signals also unbolt. They get relocated onto our kit. By bolt off bolt on. I mean that there are no permanent mods to your bike.
QUESTION: How hard is it to remove the stock fender, and how much rewireing/drilling is involved to put on the new one?...
ANSWER: This is a simple install. No wiring. Pretty much unbolt the stock fender, and mount our kit. 45 min. job
QUESTION: will it fit a 2004 EX250?
ANSWER: yes, they're all the same!
QUESTION: Does this piece slid into the body (underneath the wheel well) like the factory?
ANSWER: I don't know if it slids or not, but it does fit up in the wheel well and acts as a fender from about 12" in front of the tail light, back. This is NOT a painted undertail.
QUESTION: Is this the new kit that slides up underneath the body like the existing plastic fender
ANSWER: It's a stainless steel fender eliminator. It relocates the lic plate and turnsignals.
QUESTION: will aftermarkey blinkers such as the short stalk signals fit or are the holes pre drilled ofr the factory ones
ANSWER: They are designed to fit both.
QUESTION: wit this kit do i still have the trunk area to put things in or will there be a big old hole there?
ANSWER: You will have storage.
QUESTION: Will this fit 04 models?
ANSWER: yes
QUESTION: what is in this kit for $109.95 it just looks like a plat to me i want to run my blinkers in the empty side lights on the tall ight.
ANSWER: This kit replaces the back half of the wheel-well, has a lic pan and signal bracs
Ask your question here:
Your email (so we can send you the answer):
powered by
