38 SPECIAL FRAME SLIDERS: KAWASAKI ZX6R/ RR (03-06)
Fits Kawasaki ZX6R (636), ZX6RR (03-06)
This item usually takes about 4 days to ship
Item no. 431-6300
Today$100.00
Application Chart Diagrams
Application
2003 Kawasaki ZX 6R Ninja (636)
2004 Kawasaki ZX 6R Ninja (636)
2005 Kawasaki ZX 6R Ninja (636)
2006 Kawasaki ZX 6R Ninja (636)
2003 Kawasaki ZX 6RR Ninja
2004 Kawasaki ZX 6RR Ninja
2005 Kawasaki ZX 6RR Ninja
WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations.
The Q&A on this Product
QUESTION: Will it fit on my 03 ZZR600, and do i have to do any cutting?
ANSWER: YES AND YES
QUESTION: will this fit on a 2007 zzr 600 and will i will i have to drill any holes to the fairings
ANSWER: Yes this will fit your bike and you will have to cut 1 hole on each side of your bike's fairing to access the motor mount location.
QUESTION: Will your frame slider fit a 2008 Kawasaki ZZR600?
ANSWER: yes
QUESTION: will these bad boys fit my 03 636.
plus no cutting?4/5/08
will these bad boys fit my 03 636.
T.BAG
New york
n.y
ANSWER: All Kawi's need to have the fairing cut in order to acess the motormounts. We do not use offset brackets. Offset brakets are not as stong as going directly to the frame.
QUESTION: how long is the slider or how many inches long?
ANSWER: They are roughly 3 inches plus the spacer. It also depends what model bike .The installer can also shorten the spacer.
QUESTION: wondering if a 2006 zzr 600 engine will fit into 2003 zzr600 motorbike,, kawakaski...
have 2003 ZZR 600 with blown engine, and i can see a 2006 ZZR 600 engine for sale. wondering if they will fit...thanks
ANSWER: Good question.Answer: I don't know.
QUESTION: would it fit for a 20006 kawasaki zzr 600
ANSWER: yes
QUESTION: Do I have to cut anything to install this to a 2006 kawasaki 636? thanks
ANSWER: yes
QUESTION: will your frame cliders fit the Z1000 ?
ANSWER: No,sorry
QUESTION: where do u cut on the fairing on zx9
ANSWER: Where you cut is determined by where your motormounts are.
QUESTION: I have a zx6r / 2005 / in the same color {Pearl Magna Red} as the one in your pic.
Is the picture shown the "Polished Aluminum" version or the " Chrome 1?
ANSWER: Chrome
QUESTION: will these fit 2000 zrx1100.
ANSWER: no
QUESTION: Will these fit 2000 zx6-r ?
ANSWER: Yes
QUESTION: what is the best way to find out where to mark and cut the hole to mount them on an 05 636, in other words what has worked best for you guys??
ANSWER: We found using a laser level works the best.Prop your bike on stands or a Handy Lift .Remove farings from bike. Point laser level at motor mount bolt ,replace fairings on bike. The laser will point on the fairing exactly where the motor mount bolt is on the other side of the fairing. As long as you do not move the bike or the laser level during this process it will work .Repeat prcess on the other side.You can buy a laser level very cheaply @ Home depot
QUESTION: would a simple drill work to cut the 3/4 hole in the fairing to make it fit?
ANSWER: If your drill has 3/4 inch chuck that it will work.If your drill does not have 3/4 inch chuck you can use a drill dit that has a tapered shaft or use a hole saw kit.
QUESTION: What should I use to cut the fairing on my 2006 Kawasaki 650R to mount frame sliders? What kind of blade or tool works best and how can I protect the paint?
ANSWER:
QUESTION: i have a 05 636 ninja and was wondering how user friendly the sliders are to mount, and how much cutting will i need to do to the fairing to mount them??
ANSWER: You will need to cut a 3/4 inch hole for the spacer .Or you will need to cut a hole 1 3/4 inch for the entire spacer.It all depends on how close you want to mount them to your frame.
QUESTION: do i need to do any modifications or cutting on my
zzr's frame? thanks
ANSWER: YOU SHOULD NEVER EVER HAVE TO CUT YOUR FRAME TO INSTALL A SET OF FRAME SLIDERS!! THE FRAME IS THE BACKBONE OF YOUR BIKE AND YOU DO NOT WANT TO COMPROMISE THE STRUCTUAL INTEGRITY OF YOUR FRAME.If you can access your motor mounts and they are not directly behind the fairings then you would not have to cut your fairngs.
QUESTION: Is this product strong enough to protect my 06 ZZR600?Do i have to make any modifications or cutting on my frames? thanks
ANSWER: This product is made from 6061 aircraft grade billet aluminum. It is very strong and will do it's funcution well. It is made to look good as well as serve it 's purpose.Thank You for your intrest in this product.
QUESTION: its available for zx6 2002? if isn't can you tellme wich one is the rigth one. thankyou
ANSWER: yes
QUESTION: DO YOU MAKE THEM FOR 2006 ZX6R?
ANSWER: yes
QUESTION: Will these frame sliders fit a 2003 Kawasaki ZR-7S? If not can you tell me of some sliders that do.
Mark..
ANSWER: I am sorry but we dont make parts for your bike.
QUESTION: do you have this for the 05 636
ANSWER: yes
QUESTION: can you get these on a 2001 zx6r without cutting the fairing
ANSWER: You may need to drill a 3/4 inch hole for the spacer
QUESTION: I would like some frame sliders for a 2006 Ninja 500. I love riding and I am very careful..... can you point me in the right direction?
ANSWER: Buy ours. you will love them
QUESTION: do u carry the gun that we can replace as the foot pegs on the back to match the bullet frAME SLIDERS ALSO I HAVE A 99 ZX1100 I WANT BULLET FRAME SLIDERS AND CLUTCH AND BRAKE HAND LEVER DO U HAVE THEM AND THE BAR ENDS
ANSWER: we do not make the gun. I don't know if our products will cross over to a 99 zx 1100
QUESTION: i see that it says add 49.95 for black, chrome and polished...what color comes standard?
ANSWER: those are the only colors we offer.
QUESTION: If I cut the fairing on my 2006 Ninja 500r will these work? Or do you know of any frame sliders that will work? Thanks
ANSWER: our frame sliders should fit I have never put them on a 500 But they should be the same.
QUESTION: Will these fit a 2005 ZX-6RR
ANSWER: yes the will fit that bike
QUESTION: On the 02 ZX6r, will the fairing have to be cut?
ANSWER: If you can't see the bolts that hold the motor to the frame you have to cut the fairing
QUESTION: WILL THE FRAME SLIDERS and matching 38 special levers (brake,cluch)FIT A 2000 ZX9R?Thanks
ANSWER: yesthe frame sliders will fit your bike.We do not make lever's for your bike.
QUESTION: Do these frame sliders fit a zx6e/zzr600???
ANSWER: yes
QUESTION: I am in search for frame sliders that obviously have to be customized for a
2004 zzr600.
Can you help with any information?
ANSWER: our standard slider will fit that bike
QUESTION: Do you have to cut the faring for a 99 zx6r?Thanks
ANSWER: I don't thank so as long as your frame is exposed where it bolt's to the frame.
Ask your question here:
Your email (so we can send you the answer):
powered by
