Application Chart Diagrams
Application
2006 Suzuki GSX-R 600 (K6)
2007 Suzuki GSX-R 600 (K7)
2006 Suzuki GSX-R 750 (K6)
2007 Suzuki GSX-R 750 (K7)
WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations.
The Q&A on this Product
QUESTION: can these sliders fit on a 2008 gsx-r 750
ANSWER: No they do not.
QUESTION: i would just like to know if the frame sliders are still going to say gsxr on them?
ANSWER: This item is out of stock and we will not know if it has the logo on it until we receive the item in from Puig.
QUESTION: i was wondering if i needed to torque the bolts to a specific torque after the installation or not and if so what is the torque pressure?
ANSWER: For the motor mount bolts you need to contact your suzuki dealer for torque specs.
QUESTION: can u send my any pics on the frame slider install and any instructions... i'm thinking of doing it myself
ANSWER: You would have to email jason@ofdracing.com for pics. The kit comes with instrucitons.
QUESTION: i bought a set of no cut sliders for my 07 gsxr 600. when i instaled them i had to cut a little piece of the tab on the left side fairing. do ur involve the same thing. the problem i was having is that the bracket was hitting it and not alowing the fairing t go in all the way. thanks
ANSWER: There should be no cutting of anykind required. I have mounted a couple of sets and never had a problem.
QUESTION: would you say these are better/stronger than Motovations? i hear the motovations are the best you can buy right now. with the Puig ones being less expensive, im tempted to go with them.
ANSWER: The Puig ones are a great quality slider. There have not been any complaints about them holding up. Another alternative would be the Shogun no cut sliders.
QUESTION: Hello, Will These fit a 2006 Suzuki Katana GSX750?
ANSWER: No they will not.
QUESTION: Hi, I have these frame sliders installed on my bike when I bought the new bike. Can you please send me instructions as to how I can take them off just so that in the future if I have to take off the fairings to do oil change, etc. Thanks!
ANSWER: The only instructions are the ones that came with the package.
QUESTION: i just installed the puig fram sliders. i noticed that the bracket for the left side had a bolt for the frame, plus a samller screw that looked like the screws on my plastics. whats it for? i have a gsx-r 600. is the screw for another bike?
ANSWER: If you follow the instructions the smaller screw goes in the hole on the bracket below the motor mount bolt. If you need a pic email jason@ofdracing.com.
QUESTION: When you install the sliders do you have to support the enginge or do you just pull the engine mount bolt the put the slidder in thanks for the help
ANSWER: Do one side at a time. You do not have to support the motor. Do not remove both motor mount bolts at the same time.
QUESTION: i have a set on my '05 that were crashed, but I cant seem to find them listed will these fit the '05?
ANSWER: No they only fit the 06-07 GSXR 600/750. Our supplier only has 2 of these in stock. You would have to special order them. Part# PFS1865 MSRP is $89.99
QUESTION: how do you install the bracket on the left side?
ANSWER: You would pull the fairing and then remove the motor mount bolt. You will then mount the bracket useing the long bolt supplied with the sliders and then reinstall the fairing and you are done. Took us about 30 min to install this kit on a bike, being careful since it was not out bike!
QUESTION: I am having problems installing the left side slider can you please send me instructions
ANSWER: Please email jason@ofdracing.com for installation pictures.
QUESTION: What is the length of these sliders?
ANSWER: One is 3.5 inches the other is 4.5 inches
QUESTION: i bought some other no cut frame sliders for my 06 and they made my fairing pop out of the rear gromet and my leg would hit it. i think the bracket was too big. my question is, do the fairngs stay in the stock position after the sliders are installed and are there any different colors? thanks
ANSWER: Yes the fairings stay in the stock postions. They are not available in any other colors.
QUESTION: Is the application basic enough to do it yourself?
ANSWER: Yes it is very simple.
QUESTION: are these stronger than the shogun frame sliders?
ANSWER: I don't know if they are stronger, they are just a different look. I have seen the Shogun ones crash and survive very well. I have not seen the Puig ones crashed yet.
QUESTION: What material is this constructed of? Also how thick is the offset bracket?
ANSWER: The puck is an injected Nylon. The bracket is 1/4" thick.
Ask your question here:
Your email (so we can send you the answer):
powered by
