Rumble - HONDA CBR1000RR 2004-07 FENDER ELIMINATOR BONE SERIES
This RUMBLE CONCEPT “Fender eliminator”` Bone series is made of 16
gauge sheet metal and incorporates a new designed laser cut logo.
This eliminator use seperate brackets on each side (laser cutted with CBR) that allows
you to mount any short stalk signals (1/4'' shaft) you want.
Installation is a snap by using the holes of the stock fender and without any drilling
or cutting, the New RUMBLE CONCEPT “Fender eliminators”` are the nicest
and the finest quality available.
If you’re looking for that special touch of detail for your bike, the RUMBLE CONCEPT
«Fender eliminator» is the answer with it`s nice powder coated finish.
Item no. RU27222
Today$87.09
Application Chart Diagrams
Application
2004 Honda CBR 1000 RR
2005 Honda CBR 1000 RR
2006 Honda CBR 1000 RR
2007 Honda CBR 1000 RR
WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations.
The Q&A on this Product
QUESTION: will this product fit on my cbr 1000 rr 2005 with a jardine alumnium race slip on exhaust? thank you.
ANSWER: This fender eliminator fits on the original Honda side bracket so if you kept yours it should fit.
QUESTION: I have a bike honda cbr 1000 rr 2006, and I would like to know if the gauges from a honda cbr 1000 rr 2007 would fit in my bike.
ANSWER: yes it will fit
QUESTION: i have a two brothers exhaust but its for and 07 cbr1000rr.will it fit on my 06 cbr1000rr
ANSWER: yes it will fit
QUESTION: Do you have any pictures of the Rumble-Honda cbr 1000RR 2004-2006 Fender eliminator bone series mounted on a bike? I like the product but i would like to see it on a bike.
Thanks.
ANSWER: www.rumbleimport.com for more pictures
QUESTION: I ordered the RU27222 for the cbr 1000 06 and recieved the RU27220 03-04 for the cbr 600. Will this fit my bike correctly?
ANSWER: I would need the name , so I can trace the order and send the correct part.
QUESTION: will this work with D&D slip on exhaust, the one with 2 pipes side by side
ANSWER: This product will be available in about 3 weeks, for the fender kit that will fit the aftermarket exhausts
QUESTION: Last time I looked this item was due to ship 29 Sept 06. How many times woudl you expect this item to be pushed back before you actualy begin the hsipping process?
ANSWER: This item will ship next week, if you have the after market exhaust, than we need to wait for the new fender kit.
QUESTION: can you mount the stock blinkers to this
ANSWER: no the stock blinkers might not fit its worth a try but i dont think so .
QUESTION: will this work with a arata slip on exhaust?
ANSWER: This product is being removed from our listing, we have had minor defects.
QUESTION: i have a 05 yzf-r1 and installed the rumble bone series fender eliminator. the led light for the license plate has too small of wiring for the factory connectors and it caught on fire. luckily no damage to bike, but what am i supposed to do, run without a lite?
please let me know what i can do
ANSWER: we have sold over 5000 of these lights since theyve been out its not as much a question about wirring being to thin but the way they are put it . what you can do is either call us we`ll give you a new part because its the same 12 volt voltage as any other light that size. contact us for more information about it and im sure we can help you from there with one of our experts in technicien
Ask your question here:
Your email (so we can send you the answer):
powered by
