Slik Stand
-Fits tires up to 6 1/2" wide
Powder Coated (Black only)
Heavy Duty 11 Gauge Steel
Lifetime Guarantee
Works with any Motorcycle
Tubular cross bar is 2"x2"x35"
Shoe is 22" long and 6 1/2" wide
Today$176.10
Keyhole shaped slots
in the bottom of the chock portion of the "Slik Stand"
make installing or removing it a 30 second task once the hardware
has been installed in the floor of the transporting vehicle. Simply
attach the "Slik Stand" to the floor, roll your bike into
place and attach tie downs (not included) to the cross bar and to
the motorcycle. Then haul your motorcycle to where the fun is! The
"Slik Stand" eliminates the need for "D" rings
or tie down points anywhere else.
The "Slik Stand"
makes a great work tool too! Use it to hold your bike upright and
stable for simple maintenance or major repairs. Attach either wheel
of your bike to the "Slik Stand" and the end of the motorcycle
not attached can be raised as needed by jacking or any other safe
means of lifting.
PREVENT THEFT! Once
the "Slik Stand" is attached to your pickup, van, or garage
floor you can easily lock your motorcycle to it by running a chain
or cable through the loop welded to the front of the "shoe"
and the wheel of the motorcycle.
Haul Your Motorcycle with Slik Stand
Five of us hauled
our bikes to Arizona Bike Week 2000 in this 18' enclosed trailer
over 1,500 miles of rough highway and Interstate.
Haul
Your Motorcycle on a Trailer or in a Pickup.
Working on Your Motorcycle with Slik Stand
Use
the "Slik
Stand" in the garage, the driveway, or anywhere
else that you want to stabilize your motorcycle.
Secure Your
Bike with Slik Stand
Prevent
theft!!!
Once a Slik
Stand or
"Slik
Chock"
WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations.
The Q&A on this Product
QUESTION: from alan postcod eh234nh for slik stand uk
ANSWER: Alan,
The Post Office quoted approximately $90 and 6-10 days of travel time.
Regards,
Merl
QUESTION: from alan price to send to uk
ANSWER: We need a postal code in order to quote a shipping cost.
Thanks,
Merl
QUESTION: is it possible to put two stands side by side in the back of a dodge ram for twoo sportbikes.
ANSWER: If there is room for the 2 bikes, there should be room for the Slik Stands. The crossbar is 36" wide with the chock mounted in the center of each.
Additional holes can be drilled in the crossbar to allow the chock to be moved sideways if necessary.
If you have further questions, you might call our toll free number, 877-754-5788 and ask for me.
Regards,
Merl
QUESTION: I have a F150 truck, do I really need to drill the back off my bed to carry my bike in the back.
Or can I just use tie downs?
ANSWER: To be most effective, the Slik Stand should be bolted down. Otherwise it can move around if the tie downs should lose their tension. Another option is to mount the Slik Stand to a sheet of 3/4" or 1" plywood cut to fit your bed and then use additional tie downs to anchor the bike to the pickup.
We offer the Slik Nuts for pickup beds and metal floor applications. They are user friendly and are very non-intrusive. Easy to install and should you ever decide to sell the pickup , remove them and fill the holes with plastic or metal snap-in caps available at your local hardware store.
QUESTION: Hi I'd like to become a dealer in the UK can you tell me if this is possible ?
Thanks John
www.xrstuff.co.uk
ANSWER: Hi John,
We would be happy to discuss that possibility. Please contact us at www.merl@slikstuff.com or call us at 1-719-539-0555 Monday through Friday 8-5 Colorado,USA mountain time.
Regards,
Merl Allemang
Slik Stuff, Inc.
QUESTION: Hello,
I have a Mercedes Benz Vito Van which has a hardwood floor over the vans original metal floor.
I'd like to carrier two dirt bikes, using your Slik Stand system is this feasible..?
And is there anybody in the UK that stocks this system..?
Regards & Thanks
Leigh
ANSWER: We answered this email at sales@slikstuff.com. for you last week. Powersportsfx.com is one of our dealers. This application is feasible, however we do not have any sales reps. in the U.K.
Thank You
D.J.
QUESTION: I have a trailer with 5/8 flywood floor over a metal frame. Does the stand need to be mounted through the frame or just through the plywood between the frame members? What would you recommend, and what type of fasteners would you use? Bikes are HD Road Kings
ANSWER: The Slik Stand hardware does not need to be mounted through the frame. The hardware is designed to go through the wooden floor only and is included with each unit.
It is very easy to install and all directions are included. If you have further questions, please call us toll free at 877-754-5788.
ThankS!
Merl
Ask your question here:
Your email (so we can send you the answer):
powered by
