Triumph Sprint ,Trident and Trophy Handlebar Risers
The risers are placed between the fork crown and the handlebars to raise the bars up 3/4" (19mm). This will help to relieve wrist and neck pain on long rides. Requires no change of any control cables, wiring, or hoses.
Item no. T115
Today$110.95
Application Chart Diagrams
Application
1991 Triumph Sprint
1992 Triumph Sprint
1993 Triumph Sprint
1994 Triumph Sprint
1995 Triumph Sprint
1996 Triumph Sprint
1997 Triumph Sprint
1998 Triumph Sprint
2000 Triumph Sprint RS
2001 Triumph Sprint RS
2002 Triumph Sprint RS
2003 Triumph Sprint RS
2004 Triumph Sprint RS
2005 Triumph Sprint RS
1999 Triumph Sprint ST
2000 Triumph Sprint ST
2001 Triumph Sprint ST
2002 Triumph Sprint ST
2003 Triumph Sprint ST
2004 Triumph Sprint ST
2005 Triumph Sprint ST
1991 Triumph Trident
1992 Triumph Trident
1993 Triumph Trident
1994 Triumph Trident
1995 Triumph Trident
1996 Triumph Trident
1997 Triumph Trident
1998 Triumph Trident
1999 Triumph Trident
2000 Triumph Trident
2001 Triumph Trident
2002 Triumph Trident
2003 Triumph Trident
2004 Triumph Trident
2005 Triumph Trident
1991 Triumph Trophy
1992 Triumph Trophy
1993 Triumph Trophy
1994 Triumph Trophy
1995 Triumph Trophy
How the T117 risers look installed on the Sprint ST '99.
WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations.
The Q&A on this Product
QUESTION: From the picture, it's hard to tell, but these appear to be about the same height as stock, which I measure as 1/2" on my 1996 Triumph Sprint (carb model, pre-fuel injection RS/ST versions). Would be interested in something to raise the bars/grips 1" or a little more. If these raise the position 3/4" - then they be 1/2" (OEM) + 3/4" extra and should therefore measure about 1 1/4" overall to add 3/4" lift. Am I missing something? Let me know - thanks.
ANSWER: The risers are 3/4" thick and go between your triple-clamp and handlebars. They raise the bars 3/4" higher than the stock height.
QUESTION: I have just purchased a Sprint st 2002 and was wondering do you have a rear hugger for that model and can that be shipped with the handle bar risersfor this model to save frieight???
ANSWER:
QUESTION: Also,
Before I order the riser from you I need to know if you also carry the bolt on protectors that fit on the side of most sport bikes so that if you happen to lean it over or drop it there will be very little damage to the plastic fairing and side cover? (cost and availability)
Thanks,
cliff
ANSWER:
QUESTION: do you have a riser to fit a 1996 triumph trophy and if so what is the availability and cost.
ANSWER: Hi,
We do carry risers for the 96 Trophy. They are our part # T-116 and go for $109.95. The risers are currently in stock and ready to ship.
Thanks for the inquiry,
Scott-GenMar
QUESTION:
Greeting
Will your risers fit the 2007 Triumph Sprint which already has the higher bars.
Cheers Steve
ANSWER: Hi Steve,
Our T-118 risers will fit the 07 Sprint.
Thank you,
Scott-GenMar
QUESTION: Can you ship to the UK please and at what cost?
Many thanks and kind regards
Mark
ANSWER: Hi Mark,
We do ship to the UK daily. Shipping is determined in the cart (place the order, if you don`t like the amount for shipping, then close the order), and usually arrives in around 7 days.
Thanks for the inquiry,
Scott-GenMar
QUESTION: Do you have any to fit the TT600?
ANSWER: Hi,
We currently do not carry a riser for the TT600. Sorry we couldn't help you out.
Thank you,
Scott-GenMar
Ask your question here:
Your email (so we can send you the answer):
powered by
