WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations.
The Q&A on this Product
QUESTION: will the 43mm fit my 2001 ducati 900ss. I have been told they may make switchgear and brake resoivoir hit fairing.
cheers
ANSWER: No, 43mm will not...that's the lower fork tube diameter. You would need 50's. As for the clearance - I've seen a ton of race bikes with them on there. It does move the bars slightly forward from the OEM Ducati bars...you need to look at each application to establish if there is any potential for interference and see what can be done to alleviate it.
QUESTION: I have a 1990 GSX-R 750 and would you happen to have a tripple clamp assembly and clipons for my bike that i can buy?
ANSWER: Clipons are no problem....triple clamps we definitely do not have.
QUESTION: how much is shipping to uk and what is total package cost clipons woodcraft 43mm cheers
ANSWER:
QUESTION: What is the diameter of the bars?
ANSWER: 7/8" - standard for all sportbikes.
QUESTION: I'm interested in these clips ons for a 1996 Triumph Trident 900. The manual says the forks are 43mm in diameter... is it a safe bet to buy these clip ons for it?
ANSWER: If they are standard forks - not upside down - then the 43mm is a pretty sure bet.
QUESTION: 2002 Honda f4i can I mount the clip on below the top triple tree? How?
ANSWER: The clipon clamp is 1-1/2" wide. If there is room below then you can do it. We cannot guarantee there will be no interference with stock parts. The clipons are at a 7 degree angle (like stock) and the bars are 12" long. You will have to determine if there will be interference in a full lock either side before you purchase the simple to install 2 piece split design.
QUESTION: Will the 43mm fit on a 2007 Speed Triple?
ANSWER: Definitely not. You have upside down forks that are most likely 50mm. 43mm is the diameter of the lower part of the fork.
QUESTION: will the 43mm clip ons clear the fairings and will it clear for the steering lock on a 97 suzuki bandit
ANSWER: We do not know. They are at 7 degrees like stock. The clamps are 1-1/2" wide and the bars/tubes are 1' long.
QUESTION: I have a 2000 Honda F4. Will I have to make body modifications to the fairing inorder for these clip ons to fit???
ANSWER: Yes, it may. Honda F4 series bikes, in street trim, have a small problem where the hand controls can contact the fairing when approaching full steering lock. Racers fix this easily by putting a slight bend in aftermarket fairing brackets, but the OEM bracket does not bend. I hope this information helps you.
QUESTION: What is the downangle?
Will the 50's clear the stock tank, bodywork, and air intake etc. for a CBR 954RR?
Thanks!
ANSWER: 7 degrees is the down agnle for all of our clipons. These fit right on most bikes but on the 954, in street trim, there is interference.
QUESTION: will a 43 mm clip on fit a 99 suzuki bandit 1200s?
ANSWER: We do not know. You need to measure the fork tubes with a vernier caliper in the spot you wish to mount them. The clamp is 1-1/2" high/wide.
QUESTION: will they fit on a 2004 fz1 whith 43mm front
ANSWER: They will fit the fork tubes, but we do not have data on clearance for the tank fairing or gauges for that bike. I may be OK, but you will have to take a look at your bike and decide if you think they will work.
QUESTION: Regarding the Woodcraft 43MM Clip-ons. Two questions:
1. Can you tell me the height of the clip.
2. Do the caps remove and do the bars have threaded ends for intalling my existing bar ends weights?
ANSWER: The height is 1-1/2". The delrin plug ends are installed by a force fit(you would use a dead blow hammer). If you wanted to install bar end weights you could order them and ask for the plugs NOT to be installed and you could do that later.
QUESTION: Does this come with one clippon or two.
ANSWER: It comes as a set, with bars.
QUESTION: Yamaha R6 2004. Will these fit?
ANSWER: Yes, 43mm fits that bike.
QUESTION: Will the 43mm clip ons give enough steering lock on an Yamaha XJR1300? If so I'll be very happy.
ANSWER: I cannot answer that question as I have never tried them on that motorcycle
QUESTION: Are the bar lengths longer for a CBR 954 then a CBR F4i? Please let me know. And if so, will the cbr 954 still slide & clamp into the 43mm f4i clamps?
Thankx
ANSWER: The handlebar length is universal for all bikes. They can be positioned in and out for individual rider preference. A 954 does not take 43mm clipons though, it takes 50's.
QUESTION: Will the 43MM clip ons fit my 1995 Triumph Daytona. Also are they sold as a set (both clip-ons and both bars) or just one clip-on and one bar. ....... Thank you
ANSWER: To the best of our knowledge the majority of the Triumphs take 45mm clipons. The best way is the measure the upper fork tube (clamp area is 1-1/2" high/wide) with vernier calipers to determine which size works. For example if the reading is 44.6 you would take 45's. The clipons are sold as a set but replacement bars can be purchased separately.
QUESTION: Do the clip-ons come with bars or do you have to buy them seperatly ?
ANSWER: All clipons come complete with bars.
Ask your question here:
Your email (so we can send you the answer):
powered by
