Application Chart Diagrams
Application
1999 Yamaha V-Star
2000 Yamaha V-Star
2001 Yamaha V-Star
2002 Yamaha V-Star
2003 Yamaha V-Star
2004 Yamaha V-Star
2005 Yamaha V-Star
WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations.
The Q&A on this Product
QUESTION: I would like to purchase a set of risers for my 1999 XVZ1300 Royal Star Tourer Delux. I live in Australia is this a problem? Thanks, Pete
ANSWER: Hi Pete,
Shipping to Australia is not a problem. We ship our international orders via global priority which usually takes around 7 days to arrive.
Thank you,
Scott-Genmar
QUESTION: My gf has a 2002 Vstar 650 custom and she needs something to pull the bars back towards her and maybe a little up. What do you have for that?
ANSWER: Our Y-122 risers raise the bars up 1 1/2" and back just over 1" closer to the rider due to the angle. No changes to the control cable necessary.
Thank you,
Scott-Genmar
QUESTION: Will the Y122 work on a 2007 Yamaha Venture?
ANSWER: Hi,
The Y-122 risers will fit on the 07 Venture. However, they will slightly touch the cover on the gas tank at full lock.
Thank you,
Scott-Genmar
QUESTION: Will these work on a 2006 Royal Star Venture?
ANSWER: The Y-122 risers will fit the 06 royal Star Venture.
Thank you,
scott-genmar
QUESTION: Do you have a riser for a 2005 Royal Star Tour Deluxe?
ANSWER: Hi,
We currently do not offer a riser for the 05 RSTD. Sorry we couldn't help you out.
Thanks for the inquiry,
Scott-GenMar
QUESTION: I just put the Y-122 risers on and it only took about 30 minutes for my 30 Silverado 650 but... there is a gap on the back of the risers, next to the tank. Is this normal?
ANSWER: There should be a little bit of a gap between the top clamp and the riser.
Thank you,
Scott-GenMar
QUESTION: is it still 14lbs torque?
Thank you
James & Grace Norton
ANSWER: 14-16 lbs torque is recommended.
QUESTION: Thank you it did. I went ahead and ordered the risers but i have another question about the instalation. Your instructions state that you must first put in the screws closest to the front wheel and then put on the handle bar and continue the instalation. Question: with the Y-122 this would not appear to be correct because the risers go inbetween the bars and the orrigianl equipment. How do you remove the screws so that you can put the top caps on if you install the front screws first?
I hope this makes sence.
------------------
Your Question is:
You probably have been asked this before but will they fit an 03 V Star 650 Silverado? Will it work with stock cables?
Our Answer is:
Hi, The Y-122 risers will fit the 03 V-Star 650 Silverado without any changes to the control cables. Thank you, Scott-GenMar
ANSWER: It sounds like you received the installation instructions for our universal risers that have three bolts per riser. The instructions are basically the same except you will not install the bolts until the risers, handlebars, and top caps are in place. We apologize for the confusion.
Thank you,
Scott-GenMar
QUESTION: You probably have been asked this before but will they fit an 03 V Star 650 Silverado?
Will it work with stock cables?
ANSWER: Hi,
The Y-122 risers will fit the 03 V-Star 650 Silverado without any changes to the control cables.
Thank you,
Scott-GenMar
QUESTION: do you have risers for a 2003 yamaha v-star custom that will raise more than the 1 1/2 in.
ANSWER: Hi,
We currently only carry the 1 1/2" risers.
Thanks for the inquiry,
Scott-GenMar
QUESTION: Do you have risers that will fit a 2006 Yamaha 650 V- STAR CUSTOM
ANSWER: Hi,
Our Y-122 riser will fit the 06 650 Custom. We carry them in polished aluminum or black.
Thank you,
Scott-genMar
QUESTION: Installed Y122 Risers on 2004 VStar, Bolts Seem a bit Sort if you ask me, Is this Going to be a Saftey problem, Rod
ANSWER: Hi Rod,
You should have 13-15mm of bolt going into the triple-clamp. If you have less, let us know and we will send you longer bolts.
Thank you,
Scott-genmar
QUESTION: Do the Y 125s fit the 06 Royal Star Venture or is there another riser for this bike?
ANSWER: You will need our part # Y-122 for the Royal Star Venture.
Thanks for the inquiry,
Scott-GenMar
QUESTION: The stock risers are a have a brushed crome look to them. The finish on the picture makes these look almost brass. I read these are polished aluminum. Do they have the brushed look, or are they smooth crome.
ANSWER: Hi,
We carry the risers in two finished. They are in a smooth polished finished like chrome. And a brushed aluminum finish that has a clear powdercoat finish over it.
Thanks for the inquiry,
Scott-GenMar
QUESTION: Will these work on a 2007 V-star 1100 classic? Thanks Robert
ANSWER: Hi,
The Y-122s will not fit on the 07 V-Star 1100. Our Y-125 risers are specifically made for the 07 V-Stars.
Thanks for the inquiry,
Scott-GenMar
QUESTION: I need to raise the bars a little and pull them back about 2 inches on my 2000 V-Star 1100 Classic. What do you suggest?
ANSWER: Hi,
The closest we have are the Y-122 risers which will raise your bars up 1 1/2" and get them back just over 1" closer to you. This is just about all we could go without having to replace the stock control cables with longer ones.
Thanks for the inquiry,
Scott-GenMar
QUESTION: Hello,
Do you have a riser for a 2007 V Star 1100, with about a 2" or 2 1/2" rise and maybe 1" back? And if so, what cables will need to be replaced. Thank you, Jim
ANSWER: Hi Jim,
Our risers for the 07 V-Star will raise the bars up 1 1/4" and back about 3/4". This was all we could go with the stock cables.
Thanks for the inquiry,
Scott-GenMar
QUESTION: do these risers work on a 2005 Royal Star Tour Delux? I have also installed the stainless steel control cables. Do I need to change these also?
ANSWER: Hi,
We currently do not offer a riser for the Tour Delux. We weren't able to come up with a riser that would work with the speedometer. Sorry we couldn't help you out.
Thanks for the inquiry,
Scott-GenMar
QUESTION: Do you have these for the 07 V1300?
ANSWER: Hi,
We currently do not offer a riser for the 07 V1300. The speedometer is giving us problems as far as design goes. You might check back in 3-4 weeks.
Thanks for the inquiry,
Scott-Genmar
QUESTION: I have an '05 v-star 650 and I need chrome extensions. Can you help?
ANSWER: We currently not carry the V-Star risers in Chrome. However, we do have them in a polished aluminum that looks very much like chrome.
Thank you,
Scott-GenMar
QUESTION: Will these work on a 2001 Yamaha Roadstar. If not do you have some that will? Thanks
ANSWER: Hi,
The Y-122 risers will fit on the 01 Road Star.
Thanks for the inquiry,
Scott-GenMar
QUESTION: I have a 2007 Roadstar. Will this product work on my bike? Does it move the handlebars back any?
Thank you,
Frank McKenzie
ANSWER: Hi Frank,
We do have risers for the 07 Roadstar. They are a new product of ours and we haven't had a chance to get them on the web site. They are part # y-125 and we offer them in a polished or brushed aluminum finish. We should have them on the web site this week.
Thank you,
Scott-GenMar
QUESTION: 1997 Royal Star Tour Deluxe looking for riser with 2" up and 2" back in Chrome, do you have? Ron
ANSWER: Hi Ron,
We currently only carry a 1 1/2" riser with just over 1" pull back.
Sorry we couldn't help you out.
Thank you,
Scott-Genmar
QUESTION: Will these risers fit my 2003 V-Star 1100 Classic? these risers do look like chrome, right?
I'm also looking for chrome screws to screw down the passenger seat bracket. I've lost one of my screws and need to replace them.
Also I need the little chrome caps that cover the screw heads on your handle bars, I've lost one of mine.
Thanks for your help with this...
ANSWER: Hi,
The Y-122s will fit the 03 V-Star 1100 Classic. The risers do look chrome. We currently do not carry chrome bolts. The small chrome caps are a stock Yamaha item and not something we carry.
Thanks for the inquiry,
Scott-GenMar
QUESTION: I am looking for something that will set my bars back about 2-3 inches. Stock height is fine, but wouldn't complain about 1-2 inches higher, mostly want setback vs risers. 2005 RoadStar Midnight Warrior, black anodized would be cool!
Ed
ANSWER: Hi Ed,
We currently do not carry a riser for the Warrior. Sorry we couldn't help you out.
Thanks for the inquiry,
Scott-GenMar
QUESTION: Will these work on a 2006 V-star 1100 classic silverado? Thanks Ron
ANSWER: We currently do not carry a riser for the 06 V-Star. We are in the works on the new risers and should have them ready in the next 3-4 weeks.
Thanks for the inquiry,
Scott-Genmar
QUESTION: Can I use them on a 1999 V-star 650 custom?
Thanks
Luis M Velasco
ANSWER: Hi Luis,
The Y-122 risers will work on the 99 V-Star 650 Custom.
Thanks for the inquiry,
Scott-GenMar
QUESTION: Are these chrome? How much is shipping to Canada?
ANSWER: Hi,
The risers are not chrome. They are polished aluminum and look chrome. Shiping to Canada will be $8.00 for global priority.
Thanks for the inquiry,
Scott-GenMar
Ask your question here:
Your email (so we can send you the answer):
powered by
